Rolling Steel Service Doors

Commercial Garage Doors: Service Doors

SERVICE DOOR
CESD10 Standard Heavy Duty Service Door
CESD20 Insulated Heavy Duty Service Door

FIRE RATED DOOR

CERD10 Standard Heavy Duty Fire Rated Door
CERD20 Insuated Heavy Duty Fire Rated Door

SMOKE RATED DOOR

CERD11 Standard Heavy Duty Fire & Smoke Rated Door
CERD21 Insulated Heavy Duty Fire & Smoke Rated Door

Commercial Garage Doors: Coiling/Roll Up Sheet Doors

Constructed from 26ga by 24 in wide sheets of steel roll formed with integral grooves that are hemmed together to form a continuous sheet guided vertically by roll formed guides. Sheet coils around a spring loaded shaft above the header as the door is opened. Designed with ease of installation in mind.

160C Heavy Duty 12″ Coil
157C Medium Duty 12″ Coil
150C Light Duty 9″ Coil

Service Doors

Service Doors (CESD) are manufactured from 2 5/8″ wide metal slats roll formed to interlace together to create a continuous steel curtain. They are used to provide security against entry or weather protection at exterior or interior openings in industrial, commercial, institutional and other buildings.

 

CESD10 Standard Heavy Duty Service Doors

Sizes: 30′ wide, 30′ high standard construction. Large openings to 50′ wide, 40′ high, consult factory.
Operation: Motors, chain, hand-crank or push-up designs based on size, weight or frequency of operation.
Usage: Standard construction is up to 20 cycles per day with High Cycle Construction available for doors expected to be operated more than 20 cycles per day, i.e. parking garages, sally ports.
Fast Acting Doors: For high traffic openings or where air flow or temperature control is critical, doors can be designed to operate at more than twice the speed of typical doors, or up to 2 ft./sec.
Wind Load: Doors can be configured to withstand the full range of specific wind load requirements including missile impact ratings. Also refer to WindCode Section.
Seismic Performance Validation: Specific seismic calculations can be provided for all doors that are mounted Face of Wall or Between Jambs to steel or masonry. Seismic performance validation is per ASCE 7-05.
Materials & Finishes: Standard door curtains are availalbe in 24, 22, 20 and 18 gauge galvanized steel in light gray, white or tan. Also 20 gauge 300 series stainless steel with # 4 finish or #16 B&S gauge aluminum with mill, clear or color anodized finish.
Locks: Wall mounted chain keeper or zinc plated steel slide bolt with padlock provisions
Operation: Chain hoist is standard; motor or manual operation is optional
Colors:

Warranty:

White, gray, tan

2-year warranty against defects in materials and workmanship

CESD20 Insulated Heavy Duty Service Doors

 

Sizes: 30′ wide, 30′ high standard construction. Large openings to 50′ wide, 40′ high, consult factory.
Operation: Motors, chain, hand-crank or push-up designs based on size, weight or frequency of operation.
Usage: Standard construction is up to 20 cycles per day with High Cycle Construction available for doors expected to be operated more than 20 cycles per day, i.e. parking garages, sally ports.
Fast Acting Doors: For high traffic openings or where air flow or temperature control is critical, doors can be designed to operate at more than twice the speed of typical doors, or up to 2 ft./sec.
Wind Load: Doors can be configured to withstand the full range of specific wind load requirements including missile impact ratings. Also refer to WindCode Section.
Seismic Performance Validation: Specific seismic calculations can be provided for all doors that are mounted Face of Wall or Between Jambs to steel or masonry. Seismic performance validation is per ASCE 7-05.
Materials & Finishes: Exterior and interior slats are ASTM A 653 galvanized steel with exclusive finish in light gray, tan or white (available 24/24 ga only). Powder coated finish is optional. Exterior skin is available in 24, 22, 20 and 18 gauge with combination exterior and interior slats being – 24/24, 22/24, 20/24, 18/24 and 22/22. Exterior and interior skins are also available in 22 gauge 300 series stainless steel with #4 finish and #18 B&S gauge aluminum with mill, clear or color anodized finish.

Fire Doors (CERD)

Fire Doors (CERD) are available insulated and non-insulated, provide automatic closing in the event of fire detection with governed speed control. Fire doors also designed for use as a service door to provide security and access control in openings that are not part of a required means of egress.

 

CERD10 Standard Heavy Duty Fire Rated Doors

Listings: UL Classified 4HR, 3HR, 90MIN, 1HR AND 3/4HR labels and Factory Mutual Approval.
Sizes: 30′ wide, 30′ high standard construction. Large openings to 50′ wide, 40′ high, consult factory.
Wind Load: Doors can be designed to meet specific PSF wind Load requirements.
Seismic Performance Validation: Specific seismic calculations can be provided for all doors that are mounted Face of Wall or Between Jambs to steel or masonry. Seismic performance validation is per ASCE 7-05.
Materials & Finishes: Curtains are available in 22, 20 and 18 gauge galvanized steel in light gray or tan. Powder coating is available as an option, or 20 gauge 300 series stainless steel with #4 finish. Stamped steel or cast iron endlocks are provided per UL procedure. Click HERE for additional Material & Finishes Information.
Mounting: Face of wall or between jambs in both interior and exterior walls. Approved all types for the mounting of fire doors include masonry or structural steel jambs.
Operation: Chain hoist is standard; motor or manual operation is optional

 

CERD20 Insulated Fire Doors

Listings: UL Classified 4HR, 3HR, 1 1/2HR, 3/4HR classified labels. Flame spread and smoke development index factors for the insulated fire door’s mineral wool insulation are zero.
Sizes: 30′ wide, 22′ high standard construction. Large openings to 34′ wide, consult factory.
Wind Load: Doors can be designed to meet specific PSF wind Load requirements.
Seismic Performance Validation: Specific seismic calculations can be provided for all doors that are mounted Face of Wall or Between Jambs to steel or masonry. Seismic performance validation is per ASCE 7-05.
Materials & Finishes: Exterior/Interior curtain skin – galvanized steel in light gray or tan or optional powder coating is available. 300 series stainless steel with #4 finish. Cast iron endlocks/windlocks are required per UL procedure. Click HERE for additional Material and Finishes information.
Mounting: Face of wall or between jambs in both interior and exterior walls. Approved wall types for the mounting of fire doors include masonry or structural steel jambs.
Operation: Motor, chain or crank operating systems are recommended for ease of testing and controlled automatic closing speed.

 

Smoke Rated Doors (CERD)

Smoke rated doors add tested smoke and draft control to fire doors and counter fire doors. Use to protect interior corridors and smoke barrier openings or any opening where life safety is a priority.

 

CERD11 Standard Heavy Duty Fire & Smoke Rated Door

Listings: UL Classified for fire protection and the loss of property and also UL, “S” leakage rated assembly labeled for smoke and draft control.

SmokeShield products meet the requirements of the International Building Code, 2006, Section 715.4.3. for Smoke-and-Draft Control Door Assemblies

Tested per UL 1784, the procedure for smoke-and-draft control door assemblies. Meets the requirements of NFPA 105

Sizes: 30′ wide, 25′ high standard construction. Large openings to 34′ wide, consult factory.
Wind Load: Doors can be designed to meet specific PSF wind Load requirements.
Seismic Performance Validation: Specific seismic calculations can be provided for all doors that are mounted Face of Wall or Between Jambs to steel or masonry. Seismic performance validation is per ASCE 7-05.
Materials & Finishes: Exterior/Interior curtain skin – galvanized steel in light gray or tan or optional powder coating is available. 300 series stainless steel with #4 finish. Cast iron endlocks/windlocks are required per UL procedure. Click HERE for additional Material and Finishes information.
Mounting: Face of wall or between jambs in both interior and exterior walls. Approved wall types for the mounting of fire doors include masonry or structural steel jambs.
Operation: Motor, chain or crank operating systems are recommended for ease of testing and controlled automatic closing speed.

 

CERD21 Insulated Heavy Duty Fire & Smoke Rated Door

Listings: UL Classified 4HR, 3HR, 1 1/2HR, 3/4HR classified labels. Flame spread and smoke development index factors for the insulated fire door’s mineral wool insulation are zero.
Sizes: 30′ wide, 22′ high standard construction. Large openings to 34′ wide, consult factory.
Wind Load: Doors can be designed to meet specific PSF wind Load requirements.
Seismic Performance Validation: Specific seismic calculations can be provided for all doors that are mounted Face of Wall or Between Jambs to steel or masonry. Seismic performance validation is per ASCE 7-05.
Materials & Finishes: Exterior/Interior curtain skin – galvanized steel in light gray or tan or optional powder coating is available. 300 series stainless steel with #4 finish. Cast iron endlocks/windlocks are required per UL procedure. Click HERE for additional Material and Finishes information.
Mounting: Face of wall or between jambs in both interior and exterior walls. Approved wall types for the mounting of fire doors include masonry or structural steel jambs.
Operation: Motor, chain or crank operating systems are recommended for ease of testing and controlled automatic closing speed.
Models CAD BIM Shop Drawing Specification Literature(PDF) Instruction Manual(PDF) Warranty
Fire Rated Doors
CERD10 (Standard) CMDC-RSFDOOR-10.pdf InsManual_CERD10_CERD11_CERD20_CERD21.pdf
CERD20 (Insulated) CMDC-RSFDOOR-10.pdf InsManual_CERD10_CERD11_CERD20_CERD21.pdf
Smoke Rated Doors
CERD11 InsManual_CERD10_CERD11_CERD20_CERD21.pdf
CERD21 InsManual_CERD10_CERD11_CERD20_CERD21.pdf
Service Doors
CESD10 (Standard) CMDC-RSSDOOR-10.pdf InsManual_CESD10_CESD20.pdf
CESD20 (Insulated) CMDC-RSSDOOR-10.pdf InsManual_CESD10_CESD20.pdf

When you have a warehouse, factory, transit center or other industrial facility that puts a premium on accessibility, you need quality, durable and attractive stainless steel garage doors that can take a beating and continue performing each day. At Banko Overhead Doors, we offer a selection of rolling steel service doors from Clopay® that represent the most advanced technology, as well as a blend of quality, durability and attractiveness. Best of all: You can customize options to create the ideal rolling steel service door for your operation’s unique needs. Read more about our selection of commercial steel roll-up doors, and count on Banko for Clopay products when you want the best in steel service doors.

  • Constructed of a high percentage of recycled material and designed with ease of maintenance and longevity in mind, increasing the sustainability of most applications.
  • Curtains are available in prefinished galvanized steel, stainless steel or anodized aluminum finishes. Guides, bottom bars and headplates are powder-coat finished for aesthetics and increased durability.
  • Practical innovations enhanced by the aesthetic appeal ensure that a Clopay door adds value to any building exterior, combining maximum security with modest operating costs.
  • Doors can be operated manually with a standard chain hoist, or they can be motor operated. An optional manual crank operation is also available.

Recyclable Materials

Our rolling steel garage doors are available in prefinished 24-, 22-, 20- and 18-gauge construction. No matter the gauge you choose, construction includes a high percentage of recycled material. Each individual rolling steel service door is designed for simple and easy maintenance, as well as longevity that leads to the long-term value you expect out of a significant investment.

Available Material Options

You can choose the ideal material for your needs, selecting from galvanized steel, stainless steel or anodized aluminum finishes. Each model includes three structural steel angles, powder coated and bolted together to create a guide path for the curtain. Take advantage of removable service cutouts and curtain stops for advanced flexibility. Bottom bars and headplates are also powder-coated finished for increased durability.

Innovations and Exceptional Appearance

Our rolling steel service doors from Clopay offer the most advanced in practical innovations, as well as an emphasis on aesthetic appeal that goes beyond what you typically find in an industrial setting. Clopay is known for creating products that blend quality, durability and attractiveness, and it adds value to your building exterior by providing those characteristics in rolling steel service doors, all without compromising security and operating costs.

Customized Operation

Different commercial garage door users have unique needs in rolling steel service doors. While some depend on automatic operation, others appreciate the affordability of manual crank operation. Rolling steel service doors are available in a variety of operation setups, including manual pushup, chain hoist, hank crank and motor.

Why Choose Banko?

Since 1984, Banko has been serving home and business owners throughout west central Florida. When you need rolling steel service doors or other commercial overhead door products and repair services, we respond with a huge selection and a team of expert technicians who can provide fast, effective repair and replacement services.

We only send our own full-time technicians to work at your business, never outside contractors, because we believe our own employees are best positioned to deliver on our commitment to service excellence.

Share this product:

Serving Over 100 Locations

view all of our locations

Banko Overhead doors

5329 West Crenshaw Street
Tampa, Florida 33634

877.902.2656

NEAREST LOCATION SERVED

Manatee/Sarasota

941.756.7424

Contact Us Today for a free estimate on rolling steel garage doors


Get an Estimate